MEYER EQUIPMENT - FORAGE BOX

	Meyer 3116 Rear Unload Forage Box
	3100 Series Welded Frame Construction Interlocking Latch System - Automatic open and close - No operator assistance needed Heavy Duty Drive System - Fewer moving parts - Automatic chain tighteners - Easy maintenance - PTO or hydraulic drive (PTO Pictured) Crop Savor Roof (Now Optional) - Protects against leaf loss from cross winds - Removable roof standard Floor Length: 16' 6" Overall Length: 18' 4" Weight: 3540# Main Apron: 667 H Inside Height: 94" Overall Width: All Models 97" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Roof Inside Height: All Models 94" w/Standard Roof Power Source: 540 RPM PTO Drive or Hyd. Drive Motor (All Models) Poly Bond Floor: Optional Light Kit w/Cord: Standard Flared Side (4000 only): Left or Right or Both - Optional (used w/high lift dump boxes) Side Support System: Optional Gate Delay System: Optional Truck Mount: Optional 12" Screen Side Extensions: Optional
	Meyer 3118 Rear Unload Forage Box
	3100 Series Welded Frame Construction Interlocking Latch System - Automatic open and close - No operator assistance needed Heavy Duty Drive System - Fewer moving parts - Automatic chain tighteners - Easy maintenance - PTO or hydraulic drive (PTO Pictured) Crop Savor Roof (Now Optional) - Protects against leaf loss from cross winds - Removable roof standard Floor Length: 18' 6" Overall Length: 20' 4" Weight: 3820# Main Apron: 667 H Inside Height: 94" Overall Width: All Models 97" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Roof Inside Height: All Models 94" w/Standard Roof Power Source: 540 RPM PTO Drive or Hyd. Drive Motor (All Models) Poly Bond Floor: Optional Light Kit w/Cord: Standard Flared Side (4000 only): Left or Right or Both - Optional (used w/high lift dump boxes) Side Support System: Optional Gate Delay System: Optional Truck Mount: Optional 12" Screen Side Extensions: Optional
	Meyer 3120 Rear Unload Forage Box
	3100 Series Welded Frame Construction Interlocking Latch System - Automatic open and close - No operator assistance needed Heavy Duty Drive System - Fewer moving parts - Automatic chain tighteners - Easy maintenance - PTO or hydraulic drive (PTO Pictured) Crop Savor Roof (Now Optional) - Protects against leaf loss from cross winds - Removable roof standard Floor Length: 20' 6" Overall Length: 22' 4" Weight: 4100# Main Apron: 667 H Inside Height: 94" Overall Width: All Models 97" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Roof Inside Height: All Models 94" w/Standard Roof Power Source: 540 RPM PTO Drive or Hyd. Drive Motor (All Models) Poly Bond Floor: Optional Light Kit w/Cord: Standard Flared Side (4000 only): Left or Right or Both - Optional (used w/high lift dump boxes) Side Support System: Optional Gate Delay System: Optional Truck Mount: Optional 12" Screen Side Extensions: Optional
	Meyer 3216 Front & Rear Unload Forage Box
	The 3200 frame features an all welded construction. Notice that every cross member has a gusset for added strength. We use all heavy duty structural steel in our frame, no sheet metal. Uprights and crossmembers on 32" centers. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 16'6" Overall Length: 20'2" Weight: 5000 lbs. Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models with 94" Roof Inside Height: All Models 113 1/2" with Roof Total Speed System: All Models - Low Range: 0-7.5'/min.; High Range: 0-17'/min. Removable Roof: All Models - Standard Equipment Auger Feathering Sys.: All Models - Standard Equipment Even Feed Augers: 3 Large 18" Dia. Augers. Drum Style Design w/2" Teeth Power Source: 540 RPM PTO Drive or Hydraulic Motor Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard/24" Fold Down Optional Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21.5" Safety Clutch: Standard with All Models Ind. Outfeed Clutch: Standard with All Models Poly Floor: Standard with All Models Box Tie Down Kit: Standard with All Models Main Apron Gear Box: S-26-2 w/Bronze Gears Transport Lights: Standard with All Models 12" Screen Side Extensions: Optional Truck Mount: Optional Gate Delay System: Optional
	Meyer 3218 Front & Rear Unload Forage Box
	The 3200 frame features an all welded construction. Notice that every cross member has a gusset for added strength. We use all heavy duty structural steel in our frame, no sheet metal. Uprights and crossmembers on 32" centers. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 18'6' Overall Length: 22'2" Weight: 5280 lbs. Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models with 94" Roof Inside Height: All Models 113 1/2" with Roof Total Speed System: All Models - Low Range: 0-7.5'/min.; High Range: 0-17'/min. Removable Roof: All Models - Standard Equipment Auger Feathering Sys.: All Models - Standard Equipment Even Feed Augers: 3 Large 18" Dia. Augers. Drum Style Design w/2" Teeth Power Source: 540 RPM PTO Drive or Hydraulic Motor Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard/24" Fold Down Optional Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21.5" Safety Clutch: Standard with All Models Ind. Outfeed Clutch: Standard with All Models Poly Floor: Standard with All Models Box Tie Down Kit: Standard with All Models Main Apron Gear Box: S-26-2 w/Bronze Gears Transport Lights: Standard with All Models 12" Screen Side Extensions: Optional Truck Mount: Optional Gate Delay System: Optional
	Meyer 3220 Front & Rear Unload Forage Box
	The 3200 frame features an all welded construction. Notice that every cross member has a gusset for added strength. We use all heavy duty structural steel in our frame, no sheet metal. Uprights and crossmembers on 32" centers. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 20'6" Overall Length: 24'2" Weight: 5560 lbs. Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models with 94" Roof Inside Height: All Models 113 1/2" with Roof Total Speed System: All Models - Low Range: 0-7.5'/min.; High Range: 0-17'/min. Removable Roof: All Models - Standard Equipment Auger Feathering Sys.: All Models - Standard Equipment Even Feed Augers: 3 Large 18" Dia. Augers. Drum Style Design w/2" Teeth Power Source: 540 RPM PTO Drive or Hydraulic Motor Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard/24" Fold Down Optional Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21.5" Safety Clutch: Standard with All Models Ind. Outfeed Clutch: Standard with All Models Poly Floor: Standard with All Models Box Tie Down Kit: Standard with All Models Main Apron Gear Box: S-26-2 w/Bronze Gears Transport Lights: Standard with All Models 12" Screen Side Extensions: Optional Truck Mount: Optional Gate Delay System: Optional
	Meyer 3514 Front Unload Forage Box
	The 3500 frame features an all welded construction. Notice that every cross member has a gusset for added strength. We use all heavy duty structural steel in our frame, no sheet metal. Uprights and crossmembers on 32" centers. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 14'6" Overall Length: 17'4" Weight (in pounds): 3960 Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard (24" Fold-up Opt.) Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I260 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 3514 Heavy Duty Front Unload Feeder Forage Box
	The Meyer Feeder Box is equipped with easy to use variable speed hydraulic drive power. It also comes standard with a 24" extension or an optional 36" extension (measured from box side). Both are powered up and down by an easy to use hydraulic cylinder. The Meyer Feeder Box has a bonded poly liner on the entire inside and outside of the box. This bonded poly eliminates any wear from cured silage and clean up is very easy. Truck and Trailer mounts available in all Models. Floor Length: 14'6" Overall Length: 17'4" Weight: 3960# Main Apron: 667H Power: Hydraulic Drive (Standard); PTO Drive (Optional) Hydraulic Requirements: (1750 PSI, 15 GPM) Speeds: Infninite Variable (Hydraulic) Main Aprons       (3500): 4 Chains - 667H Pintle       (4200): 4 Chains - 667X Pintle - 21,000 Tensile Augers: 2 Large 18" Diameter Augers Tapering Into Box Cross Conveyor: D662 Pintle Chain W/Angle Cross Slat Cross Conveyor Width: 22" Discharge: Either Left or Right Side Unloading Discharge Clearance Heights W/24" Conveyor Extension Minimum (Down 0°): 37" (Mounted on 1600 Trailer) Maximum (Up 45°): 57" Inside Length: 14'6" Inside Width: 7'3" Inside Height: 49" Standard; 55" (w/ Optional Treaded Wood Top Rail) Overall Width       Conveyor Up: 8'10"       Conveyor Down: 10' Height From Bottom of Frame to Top of Box: 70" Standard; 76" (W/ Optional Treated Wood Top Rail) Sides and Floor: Poly Bonded 3/4" Plywood (Both Sides) Rub Rail - Wood: Standard Emergency Stop Mechanism: Standard Light Pkg.: Standard Truck Mounted Version: Optional Recomended Truck Cab to Center of Axle Minimum: Call Factory.
	Meyer 3516 Front Unload Forage Box
	The 3500 frame features an all welded construction. Notice that every cross member has a gusset for added strength. We use all heavy duty structural steel in our frame, no sheet metal. Uprights and crossmembers on 32" centers. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 16'6" Overall Length: 19'4" Weight (in pounds): 4240 Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard (24" Fold-up Opt.) Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I260 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 3516 Heavy Duty Front Unload Feeder Forage Box
	The Meyer Feeder Box is equipped with easy to use variable speed hydraulic drive power. It also comes standard with a 24" extension or an optional 36" extension (measured from box side). Both are powered up and down by an easy to use hydraulic cylinder. The Meyer Feeder Box has a bonded poly liner on the entire inside and outside of the box. This bonded poly eliminates any wear from cured silage and clean up is very easy. Truck and Trailer mounts available in all Models. Floor Length: 16'6" Overall Length: 19'4" Weight: 4240# Main Apron: 667H Power: Hydraulic Drive (Standard); PTO Drive (Optional) Hydraulic Requirements: (1750 PSI, 15 GPM) Speeds: Infninite Variable (Hydraulic) Main Aprons       (3500): 4 Chains - 667H Pintle       (4200): 4 Chains - 667X Pintle - 21,000 Tensile Augers: 2 Large 18" Diameter Augers Tapering Into Box Cross Conveyor: D662 Pintle Chain W/Angle Cross Slat Cross Conveyor Width: 22" Discharge: Either Left or Right Side Unloading Discharge Clearance Heights W/24" Conveyor Extension Minimum (Down 0°): 37" (Mounted on 1600 Trailer) Maximum (Up 45°): 57" Inside Length: 16'6" Inside Width: 7'3" Inside Height: 49" Standard; 55" (w/ Optional Treaded Wood Top Rail) Overall Width       Conveyor Up: 8'10"       Conveyor Down: 10' Height From Bottom of Frame to Top of Box: 70" Standard; 76" (W/ Optional Treated Wood Top Rail) Sides and Floor: Poly Bonded 3/4" Plywood (Both Sides) Rub Rail - Wood: Standard Emergency Stop Mechanism: Standard Light Pkg.: Standard Truck Mounted Version: Optional Recomended Truck Cab to Center of Axle Minimum: Call Factory.
	Meyer 3518 Front Unload Forage Box
	The 3500 frame features an all welded construction. Notice that every cross member has a gusset for added strength. We use all heavy duty structural steel in our frame, no sheet metal. Uprights and crossmembers on 32" centers. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 14'6" Overall Length: 17'4" Weight (in pounds): 4520 Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard (24" Fold-up Opt.) Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I260 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 3518 Heavy Duty Front Unload Feeder Forage Box
	The Meyer Feeder Box is equipped with easy to use variable speed hydraulic drive power. It also comes standard with a 24" extension or an optional 36" extension (measured from box side). Both are powered up and down by an easy to use hydraulic cylinder. The Meyer Feeder Box has a bonded poly liner on the entire inside and outside of the box. This bonded poly eliminates any wear from cured silage and clean up is very easy. Truck and Trailer mounts available in all Models. Floor Length: 18'6" Overall Length: 21'4" Weight: 4520# Main Apron: 667H Power: Hydraulic Drive (Standard); PTO Drive (Optional) Hydraulic Requirements: (1750 PSI, 15 GPM) Speeds: Infninite Variable (Hydraulic) Main Aprons       (3500): 4 Chains - 667H Pintle       (4200): 4 Chains - 667X Pintle - 21,000 Tensile Augers: 2 Large 18" Diameter Augers Tapering Into Box Cross Conveyor: D662 Pintle Chain W/Angle Cross Slat Cross Conveyor Width: 22" Discharge: Either Left or Right Side Unloading Discharge Clearance Heights W/24" Conveyor Extension Minimum (Down 0°): 37" (Mounted on 1600 Trailer) Maximum (Up 45°): 57" Inside Length: 18'6" Inside Width: 7'3" Inside Height: 49" Standard; 55" (w/ Optional Treaded Wood Top Rail) Overall Width       Conveyor Up: 8'10"       Conveyor Down: 10' Height From Bottom of Frame to Top of Box: 70" Standard; 76" (W/ Optional Treated Wood Top Rail) Sides and Floor: Poly Bonded 3/4" Plywood (Both Sides) Rub Rail - Wood: Standard Emergency Stop Mechanism: Standard Light Pkg.: Standard Truck Mounted Version: Optional Recomended Truck Cab to Center of Axle Minimum: Call Factory.
	Meyer 4116 Rear Unload Forage Box
	4100 Series Bolted Frame Construction - More Uprights - More Cross Members - Stronger Apron Chain Interlocking Latch System - Automatic open and close - No operator assistance needed Heavy Duty Drive System - Fewer moving parts - Automatic chain tighteners - Easy maintenance - PTO or hydraulic drive (PTO Pictured) Crop Savor Roof (Now Optional) - Protects against leaf loss from cross winds - Removable roof standard Floor Length: 16' 6" Overall Length: 18' 4" Weight: 3840# Main Apron: 667 X Inside Height: 94" Overall Width: All Models 97" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Roof Inside Height: All Models 94" w/Standard Roof Power Source: 540 RPM PTO Drive or Hyd. Drive Motor (All Models) Poly Bond Floor: Optional Light Kit w/Cord: Standard Flared Side (4000 only): Left or Right or Both - Optional (used w/high lift dump boxes) Side Support System: Optional Gate Delay System: Optional Truck Mount: Optional 12" Screen Side Extensions: Optional
	Meyer 4118 Rear Unload Forage Box
	4100 Series Bolted Frame Construction - More Uprights - More Cross Members - Stronger Apron Chain Interlocking Latch System - Automatic open and close - No operator assistance needed Heavy Duty Drive System - Fewer moving parts - Automatic chain tighteners - Easy maintenance - PTO or hydraulic drive (PTO Pictured) Crop Savor Roof (Now Optional) - Protects against leaf loss from cross winds - Removable roof standard Floor Length: 18' 6" Overall Length: 20' 4" Weight: 4120# Main Apron: 667 X Inside Height: 94" Overall Width: All Models 97" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Roof Inside Height: All Models 94" w/Standard Roof Power Source: 540 RPM PTO Drive or Hyd. Drive Motor (All Models) Poly Bond Floor: Optional Light Kit w/Cord: Standard Flared Side (4000 only): Left or Right or Both - Optional (used w/high lift dump boxes) Side Support System: Optional Gate Delay System: Optional Truck Mount: Optional 12" Screen Side Extensions: Optional
	Meyer 4120 Rear Unload Forage Box
	4100 Series Bolted Frame Construction - More Uprights - More Cross Members - Stronger Apron Chain Interlocking Latch System - Automatic open and close - No operator assistance needed Heavy Duty Drive System - Fewer moving parts - Automatic chain tighteners - Easy maintenance - PTO or hydraulic drive (PTO Pictured) Crop Savor Roof (Now Optional) - Protects against leaf loss from cross winds - Removable roof standard Floor Length: 20' 6" Overall Length: 22' 4" Weight: 4400# Main Apron: 667 X Inside Height: 94" Overall Width: All Models 97" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Roof Inside Height: All Models 94" w/Standard Roof Power Source: 540 RPM PTO Drive or Hyd. Drive Motor (All Models) Poly Bond Floor: Optional Light Kit w/Cord: Standard Flared Side (4000 only): Left or Right or Both - Optional (used w/high lift dump boxes) Side Support System: Optional Gate Delay System: Optional Truck Mount: Optional 12" Screen Side Extensions: Optional
	Meyer 4122 Rear Unload Forage Box
	4100 Series Bolted Frame Construction - More Uprights - More Cross Members - Stronger Apron Chain Interlocking Latch System - Automatic open and close - No operator assistance needed Heavy Duty Drive System - Fewer moving parts - Automatic chain tighteners - Easy maintenance - PTO or hydraulic drive (PTO Pictured) Crop Savor Roof (Now Optional) - Protects against leaf loss from cross winds - Removable roof standard Floor Length: 22'6" Overall Length: 24'4" Weight: 4680# Main Apron: 667 X Inside Height: 94" Overall Width: All Models 97" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Roof Inside Height: All Models 94" w/Standard Roof Power Source: 540 RPM PTO Drive or Hyd. Drive Motor (All Models) Poly Bond Floor: Optional Light Kit w/Cord: Standard Flared Side (4000 only): Left or Right or Both - Optional (used w/high lift dump boxes) Side Support System: Optional Gate Delay System: Optional Truck Mount: Optional 12" Screen Side Extensions: Optional
	Meyer 4216 Front & Rear Unload Forage Box
	The 4200 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 16'6" Overall Length: 20'2" Weight: 5340 lbs. Main Apron: 667X Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models with 94" Roof Inside Height: All Models 113 1/2" with Roof Total Speed System: All Models - Low Range: 0-7.5'/min.; High Range: 0-17'/min. Removable Roof: All Models - Standard Equipment Auger Feathering Sys.: All Models - Standard Equipment Even Feed Augers: 3 Large 18" Dia. Augers. Drum Style Design w/2" Teeth Power Source: 540 RPM PTO Drive or Hydraulic Motor Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard/24" Fold Down Optional Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21.5" Safety Clutch: Standard with All Models Ind. Outfeed Clutch: Standard with All Models Poly Floor: Standard with All Models Box Tie Down Kit: Standard with All Models Main Apron Gear Box: S-26-2 w/Bronze Gears Transport Lights: Standard with All Models 12" Screen Side Extensions: Optional Truck Mount: Optional Gate Delay System: Optional
	Meyer 4216 Industrial Duty Front & Rear Unload Feeder Forage Box
	The Meyer Feeder Box is equipped with easy to use variable speed hydraulic drive power. It also comes standard with a 24" extension or an optional 36" extension (measured from box side). Both are powered up and down by an easy to use hydraulic cylinder. Model 4200 Front and Rear unload is fast and easy to switch. Move two hose couplings and move gear box drive. That's it!! The Meyer Feeder Box has a bonded poly liner on the entire inside and outside of the box. This bonded poly eliminates any wear from cured silage and clean up is very easy. Truck and Trailer mounts available in all Models. Floor Length: 16'6" Overall Length: 20'2" Weight: 5340# Main Apron: 667X Power: Hydraulic Drive (Standard); PTO Drive (Optional) Hydraulic Requirements: (1750 PSI, 15 GPM) Speeds: Infninite Variable (Hydraulic) Main Aprons       (3500): 4 Chains - 667H Pintle       (4200): 4 Chains - 667X Pintle - 21,000 Tensile Augers: 2 Large 18" Diameter Augers Tapering Into Box Cross Conveyor: D662 Pintle Chain W/Angle Cross Slat Cross Conveyor Width: 22" Discharge: Either Left or Right Side Unloading Discharge Clearance Heights W/24" Conveyor Extension Minimum (Down 0°): 37" (Mounted on 1600 Trailer) Maximum (Up 45°): 57" Inside Length: 16'6" Inside Width: 7'3" Inside Height: 49" Standard; 55" (w/ Optional Treaded Wood Top Rail) Overall Width       Conveyor Up: 8'10"       Conveyor Down: 10' Height From Bottom of Frame to Top of Box: 70" Standard; 76" (W/ Optional Treated Wood Top Rail) Sides and Floor: Poly Bonded 3/4" Plywood (Both Sides) Rub Rail - Wood: Standard Emergency Stop Mechanism: Standard Light Pkg.: Standard Truck Mounted Version: Optional Recomended Truck Cab to Center of Axle Minimum: Call Factory.
	Meyer 4218 Front & Rear Unload Forage Box
	The 4200 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 18'6" Overall Length: 22'2" Weight: 5620 lbs. Main Apron: 667X Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models with 94" Roof Inside Height: All Models 113 1/2" with Roof Total Speed System: All Models - Low Range: 0-7.5'/min.; High Range: 0-17'/min. Removable Roof: All Models - Standard Equipment Auger Feathering Sys.: All Models - Standard Equipment Even Feed Augers: 3 Large 18" Dia. Augers. Drum Style Design w/2" Teeth Power Source: 540 RPM PTO Drive or Hydraulic Motor Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard/24" Fold Down Optional Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21.5" Safety Clutch: Standard with All Models Ind. Outfeed Clutch: Standard with All Models Poly Floor: Standard with All Models Box Tie Down Kit: Standard with All Models Main Apron Gear Box: S-26-2 w/Bronze Gears Transport Lights: Standard with All Models 12" Screen Side Extensions: Optional Truck Mount: Optional Gate Delay System: Optional
	Meyer 4218 Industrial Duty Front & Rear Unload Feeder Forage Box
	The Meyer Feeder Box is equipped with easy to use variable speed hydraulic drive power. It also comes standard with a 24" extension or an optional 36" extension (measured from box side). Both are powered up and down by an easy to use hydraulic cylinder. Model 4200 Front and Rear unload is fast and easy to switch. Move two hose couplings and move gear box drive. That's it!! The Meyer Feeder Box has a bonded poly liner on the entire inside and outside of the box. This bonded poly eliminates any wear from cured silage and clean up is very easy. Truck and Trailer mounts available in all Models. Floor Length: 18'6" Overall Length: 22'2" Weight: 5620# Main Apron: 667X Power: Hydraulic Drive (Standard); PTO Drive (Optional) Hydraulic Requirements: (1750 PSI, 15 GPM) Speeds: Infninite Variable (Hydraulic) Main Aprons       (3500): 4 Chains - 667H Pintle       (4200): 4 Chains - 667X Pintle - 21,000 Tensile Augers: 2 Large 18" Diameter Augers Tapering Into Box Cross Conveyor: D662 Pintle Chain W/Angle Cross Slat Cross Conveyor Width: 22" Discharge: Either Left or Right Side Unloading Discharge Clearance Heights W/24" Conveyor Extension Minimum (Down 0°): 37" (Mounted on 1600 Trailer) Maximum (Up 45°): 57" Inside Length: 18'6" Inside Width: 7'3" Inside Height: 49" Standard; 55" (w/ Optional Treaded Wood Top Rail) Overall Width       Conveyor Up: 8'10"       Conveyor Down: 10' Height From Bottom of Frame to Top of Box: 70" Standard; 76" (W/ Optional Treated Wood Top Rail) Sides and Floor: Poly Bonded 3/4" Plywood (Both Sides) Rub Rail - Wood: Standard Emergency Stop Mechanism: Standard Light Pkg.: Standard Truck Mounted Version: Optional Recomended Truck Cab to Center of Axle Minimum: Call Factory.
	Meyer 4220 Front & Rear Unload Forage Box
	The 4200 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 20'6" Overall Length: 24'2" Weight: 5900 lbs. Main Apron: 667X Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models with 94" Roof Inside Height: All Models 113 1/2" with Roof Total Speed System: All Models - Low Range: 0-7.5'/min.; High Range: 0-17'/min. Removable Roof: All Models - Standard Equipment Auger Feathering Sys.: All Models - Standard Equipment Even Feed Augers: 3 Large 18" Dia. Augers. Drum Style Design w/2" Teeth Power Source: 540 RPM PTO Drive or Hydraulic Motor Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard/24" Fold Down Optional Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21.5" Safety Clutch: Standard with All Models Ind. Outfeed Clutch: Standard with All Models Poly Floor: Standard with All Models Box Tie Down Kit: Standard with All Models Main Apron Gear Box: S-26-2 w/Bronze Gears Transport Lights: Standard with All Models 12" Screen Side Extensions: Optional Truck Mount: Optional Gate Delay System: Optional
	Meyer 4220 Industrial Duty Front & Rear Unload Feeder Forage Box
	The Meyer Feeder Box is equipped with easy to use variable speed hydraulic drive power. It also comes standard with a 24" extension or an optional 36" extension (measured from box side). Both are powered up and down by an easy to use hydraulic cylinder. Model 4200 Front and Rear unload is fast and easy to switch. Move two hose couplings and move gear box drive. That's it!! The Meyer Feeder Box has a bonded poly liner on the entire inside and outside of the box. This bonded poly eliminates any wear from cured silage and clean up is very easy. Truck and Trailer mounts available in all Models. Floor Length: 20'6 Overall Length: 24'2" Weight: 5900# Main Apron: 667X Power: Hydraulic Drive (Standard); PTO Drive (Optional) Hydraulic Requirements: (1750 PSI, 15 GPM) Speeds: Infninite Variable (Hydraulic) Main Aprons       (3500): 4 Chains - 667H Pintle       (4200): 4 Chains - 667X Pintle - 21,000 Tensile Augers: 2 Large 18" Diameter Augers Tapering Into Box Cross Conveyor: D662 Pintle Chain W/Angle Cross Slat Cross Conveyor Width: 22" Discharge: Either Left or Right Side Unloading Discharge Clearance Heights W/24" Conveyor Extension Minimum (Down 0°): 37" (Mounted on 1600 Trailer) Maximum (Up 45°): 57" Inside Length: 20'6 Inside Width: 7'3" Inside Height: 49" Standard; 55" (w/ Optional Treaded Wood Top Rail) Overall Width       Conveyor Up: 8'10"       Conveyor Down: 10' Height From Bottom of Frame to Top of Box: 70" Standard; 76" (W/ Optional Treated Wood Top Rail) Sides and Floor: Poly Bonded 3/4" Plywood (Both Sides) Rub Rail - Wood: Standard Emergency Stop Mechanism: Standard Light Pkg.: Standard Truck Mounted Version: Optional Recomended Truck Cab to Center of Axle Minimum: Call Factory.
	Meyer 4222 Industrial Duty Front & Rear Unload Feeder Forage Box
	The Meyer Feeder Box is equipped with easy to use variable speed hydraulic drive power. It also comes standard with a 24" extension or an optional 36" extension (measured from box side). Both are powered up and down by an easy to use hydraulic cylinder. Model 4200 Front and Rear unload is fast and easy to switch. Move two hose couplings and move gear box drive. That's it!! The Meyer Feeder Box has a bonded poly liner on the entire inside and outside of the box. This bonded poly eliminates any wear from cured silage and clean up is very easy. Truck and Trailer mounts available in all Models. Floor Length: 22'6" Overall Length: 26'2" Weight: 6180# Main Apron: 667X Power: Hydraulic Drive (Standard); PTO Drive (Optional) Hydraulic Requirements: (1750 PSI, 15 GPM) Speeds: Infninite Variable (Hydraulic) Main Aprons       (3500): 4 Chains - 667H Pintle       (4200): 4 Chains - 667X Pintle - 21,000 Tensile Augers: 2 Large 18" Diameter Augers Tapering Into Box Cross Conveyor: D662 Pintle Chain W/Angle Cross Slat Cross Conveyor Width: 22" Discharge: Either Left or Right Side Unloading Discharge Clearance Heights W/24" Conveyor Extension Minimum (Down 0°): 37" (Mounted on 1600 Trailer) Maximum (Up 45°): 57" Inside Length: 22'6" Inside Width: 7'3" Inside Height: 49" Standard; 55" (w/ Optional Treaded Wood Top Rail) Overall Width       Conveyor Up: 8'10"       Conveyor Down: 10' Height From Bottom of Frame to Top of Box: 70" Standard; 76" (W/ Optional Treated Wood Top Rail) Sides and Floor: Poly Bonded 3/4" Plywood (Both Sides) Rub Rail - Wood: Standard Emergency Stop Mechanism: Standard Light Pkg.: Standard Truck Mounted Version: Optional Recomended Truck Cab to Center of Axle Minimum: Call Factory.
	Meyer 4516 Front Unload Forage Box
	The 4500 and 4600 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 14'6" Overall Length: 17'4" Weight (in pounds): 4480 Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard (24" Fold-up Opt.) Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I260 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 4518 Front Unload Forage Box
	The 4500 and 4600 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. Floor Length: 18'6" Overall Length: 21'4" Weight (in pounds): 4760 Main Apron: 667H Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 12" Extension Standard (24" Fold-up Opt.) Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I260 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 4616 Front Unload Forage Box
	The 4500 and 4600 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. 4600 Series Industrial Duty Difference I280 Main Apron Gear Box - Twice as strong as all other brands 667X Main Apron Chain - 4-21,000# tensile = 84,000# combined tensile strength Main Apron Drive Shaft - Double strength tubing Fold Up Cross Conveyor Ext. - Standard Equipment Floor Length: 16'6" Overall Length: 19'4" Weight (in pounds): 4680 Main Apron: 667X Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 24" Fold-up Standard Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I280 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 4618 Front Unload Forage Box
	The 4500 and 4600 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. 4600 Series Industrial Duty Difference I280 Main Apron Gear Box - Twice as strong as all other brands 667X Main Apron Chain - 4-21,000# tensile = 84,000# combined tensile strength Main Apron Drive Shaft - Double strength tubing Fold Up Cross Conveyor Ext. - Standard Equipment Floor Length: 18'6" Overall Length: 21'4 Weight (in pounds): 5240 Main Apron: 667X Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 24" Fold-up Standard Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I280 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 4620 Front Unload Forage Box
	The 4500 and 4600 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. 4600 Series Industrial Duty Difference I280 Main Apron Gear Box - Twice as strong as all other brands 667X Main Apron Chain - 4-21,000# tensile = 84,000# combined tensile strength Main Apron Drive Shaft - Double strength tubing Fold Up Cross Conveyor Ext. - Standard Equipment Floor Length: 20'6" Overall Length: 23'4" Weight (in pounds): 5240 Main Apron: 667X Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 24" Fold-up Standard Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I280 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 4622 Front Unload Forage Box
	The 4500 and 4600 frame features a bolted construction. The 1/2" bolts and lock nuts fasten the cross members to the main stringers every 24". You won't find any sheet metal in the Meyer frame. TSS Control Panel - Simple yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mn. High range gives you the fastest clean-out in the industry - up to 17'/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension A convenient cross conveyor extension is available to accomodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Standard on 4600 series. Low Maintenance - Easy Access All roller chains have automatic nylon tighteners. Auger and conveyor bearings are sealed for your convenience. Variable speed sheaves have 1/2" drive pins, not 3/8". TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed on the market. 4600 Series Industrial Duty Difference I280 Main Apron Gear Box - Twice as strong as all other brands 667X Main Apron Chain - 4-21,000# tensile = 84,000# combined tensile strength Main Apron Drive Shaft - Double strength tubing Fold Up Cross Conveyor Ext. - Standard Equipment Floor Length: 22'6" Overall Length: 25'4" Weight (in pounds): 5520 Main Apron: 667X Overall Width: All Models 107" Inside Width: All Models 87" Overall Height: All Models 113 1/2" w/Std. Roof Inside Height: All Models 94" w/Std. Roof TSS - Total Speed System: All Models - Low Range: 0 - 7.5'/minute High Range: 0 - 17'/minute Quick Removable Roof: All Models - Standard Equipment Auger Feathering System: All Models - Standard Equipment Unloading, Even Feed Augers: 3 Large 18" Diameter Augers. Drum Style Design w/2" Auger Teeth Power Source: 540 RPM PTO Drive or Hydraulic Drive Motor (All Models) Cross Conveyor Feed Delivery: Either Left or Right Hand Discharge Cross Conveyor Outfeed: 24" Fold-up Standard Cross Conveyor Chain: D662 Pintle Chain w/ Hold-Downs Cross Conveyor Width: All Models - 21" Safety Clutch: All Models - Standard Equipment IOC - Independant Outfeed Clutch: All Models - Standard Equipment Poly Floor: Optional Box Tie Down Kit & Transport Lights: All Models - Standard Equipment Main Apron Gear Box: I280 w/bronze Side Support System: Optional on all Models 12" Higher Sides (expanded metal): Optional on all Models Hyd. Front Drive: Optional on all Models
	Meyer 6220 Front& Rear Unload Forage Box
	6200 Series - Commercial Grade STRENGTH - SPEED - SIZE - PRODUCTIVITY THE 6200 HAS IT ALL! Bullet Proof, All Steel Frame, Massive, High Performance Gear Boxes, High Impact, Solid Poly Floor, High Capacity 7' Sides with 4th Beater, Fastest Unload Time in the Industry. TSS Control Panel - Simple, yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mm. High range gives you the fastest clean-out in the industry - up to 17/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension with assist shock - A convenient cross conveyor extension is standard to accommodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Solid Poly Floor is Standard Equipment - Superslide, solid poly floor eliminates excess wear on apron chains, floor and gearboxes. Solid poly is impact resistant and can't delaminate. TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed. Fourth beater standard on 6200 box. Commercial-Grade Gearboxes Dwarf the Competition - Large drive couplers for switching front to rear. New TSS Speed Ratio Provides more Efficient Performance for Larger Loads. Less moving parts, spring loaded roller and chain tightening. Massive All Steel Frame - Frame is made of 16" upright/member spacing bars. Floor is solid poly on tubular frame supports. Four bolt, upright attachment. Floor Length: 20'6" Overall Length: 24'5 Inside Height (w/o roof): 7' Overall Height (w/o roof)       - top of side: 105"      - top of door pivot (+3" gds): 114"      *Less 4" truck & trailer mounts Overall Height (w/roof): 126" Inside Width: 87" Overall Width w/conveyor extension up: 109.5" Stringer Width/Height      - Truck/Trailer Mount: 33.5"/6"      - Wagon Mount: 42"/10" Weight (less options): 7,465# Capacity (struck level) cu. ft. w/o roof: 1040 Front Apron Drive Shaft: 2" Rear Drive Roller: 2 1/2" Hvy Tubing Upright Spacing: 16" Floor Supports (all steel - 16" centers): 2x2 tubing Double - 3" Angle Top Rail (no side supports needed): Standard Commercial Grade Gearbox/Drive Coupler: Standard TSS-Total Speed System - Variable Speed Low Range 0-7.5'/minute High Range 0-17'/minute: Standard Apron Chains (heavy duty pintle): 667X Spring Loaded/Torsion Style Apron Tightener: Standard Auger Feathering System & Conveyor Clutch: Standard Cross Conveyor Chain Hold-Downs: Standard Superslide, Solid Poly Floor (no plywood): Standard All Steel Frame - 16" centers (no wood): Standard 7' Sides w/4th Beater System: Standard Fold-Down Conveyor Extension w/lift assist: Standard Rear Gate Delay System (with ground control): Standard Hydraulic Front Drive System: Optional Roof Assembly (removable): Optional Rear Grain Kit-False Front Gate for Grain Kit: Optional Truck Mnt./Trailer Mnt./Wagon Mnt.: Optional Tarp Systems (w/front enclosures) Front to Back Scissor Tarp (electric) Side to Side Roll Tarp (electric): Optional
	Meyer 6222 Front & Rear Unload Forage Box
	6200 Series - Commercial Grade STRENGTH - SPEED - SIZE - PRODUCTIVITY THE 6200 HAS IT ALL! Bullet Proof, All Steel Frame, Massive, High Performance Gear Boxes, High Impact, Solid Poly Floor, High Capacity 7' Sides with 4th Beater, Fastest Unload Time in the Industry. TSS Control Panel - Simple, yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mm. High range gives you the fastest clean-out in the industry - up to 17/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension with assist shock - A convenient cross conveyor extension is standard to accommodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Solid Poly Floor is Standard Equipment - Superslide, solid poly floor eliminates excess wear on apron chains, floor and gearboxes. Solid poly is impact resistant and can't delaminate. TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed. Fourth beater standard on 6200 box. Commercial-Grade Gearboxes Dwarf the Competition - Large drive couplers for switching front to rear. New TSS Speed Ratio Provides more Efficient Performance for Larger Loads. Less moving parts, spring loaded roller and chain tightening. Massive All Steel Frame - Frame is made of 16" upright/member spacing bars. Floor is solid poly on tubular frame supports. Four bolt, upright attachment. Floor Length: 22'6" Overall Length: 26'5" Inside Height (w/o roof): 7' Overall Height (w/o roof)       - top of side: 105"      - top of door pivot (+3" gds): 114"      *Less 4" truck & trailer mounts Overall Height (w/roof): 126" Inside Width: 87" Overall Width w/conveyor extension up: 109.5" Stringer Width/Height      - Truck/Trailer Mount: 33.5"/6"      - Wagon Mount: 42"/10" Weight (less options): 7,840# Capacity (struck level) cu. ft. w/o roof: 1142 Front Apron Drive Shaft: 2" Rear Drive Roller: 2 1/2" Hvy Tubing Upright Spacing: 16" Floor Supports (all steel - 16" centers): 2x2 tubing Double - 3" Angle Top Rail (no side supports needed): Standard Commercial Grade Gearbox/Drive Coupler: Standard TSS-Total Speed System - Variable Speed       Low Range 0-7.5'/minute       High Range 0-17'/minute: Standard Apron Chains (heavy duty pintle): 667X Spring Loaded/Torsion Style Apron Tightener: Standard Auger Feathering System & Conveyor Clutch: Standard Cross Conveyor Chain Hold-Downs: Standard Superslide, Solid Poly Floor (no plywood): Standard All Steel Frame - 16" centers (no wood): Standard 7' Sides w/4th Beater System: Standard Fold-Down Conveyor Extension w/lift assist: Standard Rear Gate Delay System (with ground control): Standard Hydraulic Front Drive System: Optional Roof Assembly (removable): Optional Rear Grain Kit-False Front Gate for Grain Kit: Optional Truck Mnt./Trailer Mnt./Wagon Mnt.: Optional Tarp Systems (w/front enclosures)       Front to Back Scissor Tarp (electric)       Side to Side Roll Tarp (electric): Optional
	Meyer 6224 Front & Rear Unload Forage Box
	6200 Series - Commercial Grade STRENGTH - SPEED - SIZE - PRODUCTIVITY THE 6200 HAS IT ALL! Bullet Proof, All Steel Frame, Massive, High Performance Gear Boxes, High Impact, Solid Poly Floor, High Capacity 7' Sides with 4th Beater, Fastest Unload Time in the Industry. TSS Control Panel - Simple, yet Efficient The TSS design allows the operator more speed selections with less moving parts. Low range is 0 - 7'6"/mm. High range gives you the fastest clean-out in the industry - up to 17/mn. Plus, the Independent Cross Conveyor Clutch allows you to feather start your cross conveyor on big loads. Cross Conveyor Extension with assist shock - A convenient cross conveyor extension is standard to accommodate large tires or hard to get at spots. It extends out 24" and can be folded up when traveling. Solid Poly Floor is Standard Equipment - Superslide, solid poly floor eliminates excess wear on apron chains, floor and gearboxes. Solid poly is impact resistant and can't delaminate. TSS Auger Design Auger Feathering System allows the operator to inch the augers clean without bringing the load forward. This is accomplished through the variable speed drive. No extra belts. Notice the large 18" augers (not beaters) are tapered back more than others for the most even feed. Fourth beater standard on 6200 box. Commercial-Grade Gearboxes Dwarf the Competition - Large drive couplers for switching front to rear. New TSS Speed Ratio Provides more Efficient Performance for Larger Loads. Less moving parts, spring loaded roller and chain tightening. Massive All Steel Frame - Frame is made of 16" upright/member spacing bars. Floor is solid poly on tubular frame supports. Four bolt, upright attachment. Floor Length: 24'6" Overall Length: 28'5" Inside Height (w/o roof): 7' Overall Height (w/o roof)       - top of side: 105"      - top of door pivot (+3" gds): 114"      *Less 4" truck & trailer mounts Overall Height (w/roof): 126" Inside Width: 87" Overall Width w/conveyor extension up: 109.5" Stringer Width/Height      - Truck/Trailer Mount: 33.5"/6"      - Wagon Mount: 42"/10" Weight (less options): 8,235# Capacity (struck level) cu. ft. w/o roof: 1243 Front Apron Drive Shaft: 2" Rear Drive Roller: 2 1/2" Hvy Tubing Upright Spacing: 16" Floor Supports (all steel - 16" centers): 2x2 tubing Double - 3" Angle Top Rail (no side supports needed): Standard Commercial Grade Gearbox/Drive Coupler: Standard TSS-Total Speed System - Variable Speed       Low Range 0-7.5'/minute       High Range 0-17'/minute: Standard Apron Chains (heavy duty pintle): 667X Spring Loaded/Torsion Style Apron Tightener: Standard Auger Feathering System & Conveyor Clutch: Standard Cross Conveyor Chain Hold-Downs: Standard Superslide, Solid Poly Floor (no plywood): Standard All Steel Frame - 16" centers (no wood): Standard 7' Sides w/4th Beater System: Standard Fold-Down Conveyor Extension w/lift assist: Standard Rear Gate Delay System (with ground control): Standard Hydraulic Front Drive System: Optional Roof Assembly (removable): Optional Rear Grain Kit-False Front Gate for Grain Kit: Optional Truck Mnt./Trailer Mnt./Wagon Mnt.: Optional Tarp Systems (w/front enclosures)       Front to Back Scissor Tarp (electric)       Side to Side Roll Tarp (electric): Optional
	Meyer 8118 Industrial Rear Unload Forage Box
	8100 Industrial Rear Unload - "THE BOSS" Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: -16" Centers on Tubular Uprights -16" Centers on Tubluar Floor Supports -16" Centers on Channel Cross Members -The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 18' Inside Width: 97" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 18'9" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Hgt. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 880 Capacity (cu. ft. w/ extension): 945 Max Net Load: 25 ton Roller Chain Drive - Aprons: #80-120 Apron Chains (Pintle): 667XH H.P. Requirements: 50 HP Rear Drive Shaft: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): PTO or Hyd. Unload Time - PTO Drive: 30 sec. Clad Tuff fiberglass woven panels on sides: Standard High molecular poly floor: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Chain Oiler: Standard Transport Lighting: Standard Personalized Farm Name: Standard Stainless Steel Sides - Front/Back: Optional 14" Removable Side Extension: Optional Gate Delay System: Optional Double Center Opening Doors: Optional Hydraulic Drive: Optional Grain Kit: Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Wagon Mount Kit: Optional Front to Back Scissor Tarp: Optional Side to Side Roll Tarp: Optional
	Meyer 8120 Industrial Rear Unload Forage Box
	8100 Industrial Rear Unload - "THE BOSS" Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: -16" Centers on Tubular Uprights -16" Centers on Tubluar Floor Supports -16" Centers on Channel Cross Members -The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 20' Inside Width: 97" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 20'9" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Hgt. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 960 Capacity (cu. ft. w/ extension): 1110 Max Net Load: 25 ton Roller Chain Drive - Aprons: #80-120 Apron Chains (Pintle): 667XH H.P. Requirements: 50 HP Rear Drive Shaft: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): PTO or Hyd. Unload Time - PTO Drive: 30 sec. Clad Tuff fiberglass woven panels on sides: Standard High molecular poly floor: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Chain Oiler: Standard Transport Lighting: Standard Personalized Farm Name: Standard Stainless Steel Sides - Front/Back: Optional 14" Removable Side Extension: Optional Gate Delay System: Optional Double Center Opening Doors: Optional Hydraulic Drive: Optional Grain Kit: Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Wagon Mount Kit: Optional Front to Back Scissor Tarp: Optional Side to Side Roll Tarp: Optional
	Meyer 8122 Industrial Rear Unload Forage Box
	8100 Industrial Rear Unload - "THE BOSS" Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: -16" Centers on Tubular Uprights -16" Centers on Tubluar Floor Supports -16" Centers on Channel Cross Members -The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 22' Inside Width: 97" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 22'9" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Hgt. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 1075 Capacity (cu. ft. w/ extension): 1280 Max Net Load: 25 ton Roller Chain Drive - Aprons: #80-120 Apron Chains (Pintle): 667XH H.P. Requirements: 50 HP Rear Drive Shaft: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): PTO or Hyd. Unload Time - PTO Drive: 30 sec. Clad Tuff fiberglass woven panels on sides: Standard High molecular poly floor: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Chain Oiler: Standard Transport Lighting: Standard Personalized Farm Name: Standard Stainless Steel Sides - Front/Back: Optional 14" Removable Side Extension: Optional Gate Delay System: Optional Double Center Opening Doors: Optional Hydraulic Drive: Optional Grain Kit: Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Wagon Mount Kit: Optional Front to Back Scissor Tarp: Optional Side to Side Roll Tarp: Optional
	Meyer 8124 Industrial Rear Unload Forage Box
	8100 Industrial Rear Unload - "THE BOSS" Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: -16" Centers on Tubular Uprights -16" Centers on Tubluar Floor Supports -16" Centers on Channel Cross Members -The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 24'8" Inside Width: 97" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 25'5" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Hgt. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 1200 Capacity (cu. ft. w/ extension): 1400 Max Net Load: 25 ton Roller Chain Drive - Aprons: #80-120 Apron Chains (Pintle): 667XH H.P. Requirements: 50 HP Rear Drive Shaft: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): PTO or Hyd. Unload Time - PTO Drive: 30 sec. Clad Tuff fiberglass woven panels on sides: Standard High molecular poly floor: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Chain Oiler: Standard Transport Lighting: Standard Personalized Farm Name: Standard Stainless Steel Sides - Front/Back: Optional 14" Removable Side Extension: Optional Gate Delay System: Optional Double Center Opening Doors: Optional Hydraulic Drive: Optional Grain Kit: Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Wagon Mount Kit: Optional Front to Back Scissor Tarp: Optional Side to Side Roll Tarp: Optional
	Meyer 9124 Industrial Rear Unload Forage Box
	9100 Series Difference Our Proven 8100 "Boss" Design - Plus: *Double drive main roller #120 x 2 *High capacity hydraulic drive *Reinforced, enclosed side frame *Stainless steel sides *Gate delay system *Marker lights and DOT reflective tape *Lengths up to 36' All Standard Equipment Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: - 16" Centers on Tubular Uprights - 16" Centers on Tubular Floor Supports - 16" Centers on Channel Cross Members - The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 24' 8" Inside Width: 98" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 25'5" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Ht. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 1200 Capacity (cu. ft. w/ extension): 1400 Max Net Load: 25 ton Roller Chain Drive - Aprons: #120 Apron Chains (Pintle): 667XH Rear Drive Shaft - Heavy Duty: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): Hydraulic Unload Time - PTO Drive (Approx): 40 sec. Stainless Steel Sides - Front & Back: Standard Superslide Solid Poly Floor: Standard Gate Delay System: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Roller Chain Oiler: Standard Rear Lights, Marker Lights & D.O.T. Tape: Standard Personalized Farm Name: Standard 14" Removable Side Extension: Optional Double Center Opening Doors: Optional Grain Kit (Top Pivot Door Only): Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Front to Back Scissor Tarp (Electric): Optional Side to Side Roll Tarp (Electric): Optional
	Meyer 9126 Industrial Rear Unload Forage Box
	9100 Series Difference Our Proven 8100 "Boss" Design - Plus: *Double drive main roller #120 x 2 *High capacity hydraulic drive *Reinforced, enclosed side frame *Stainless steel sides *Gate delay system *Marker lights and DOT reflective tape *Lengths up to 36' All Standard Equipment Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: - 16" Centers on Tubular Uprights - 16" Centers on Tubular Floor Supports - 16" Centers on Channel Cross Members - The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 26' Inside Width: 98" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 26'9" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Ht. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 1260 Capacity (cu. ft. w/ extension): 1495 Max Net Load: 25 ton Roller Chain Drive - Aprons: #120 Apron Chains (Pintle): 667XH Rear Drive Shaft - Heavy Duty: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): Hydraulic Unload Time - PTO Drive (Approx): 40 sec. Stainless Steel Sides - Front & Back: Standard Superslide Solid Poly Floor: Standard Gate Delay System: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Roller Chain Oiler: Standard Rear Lights, Marker Lights & D.O.T. Tape: Standard Personalized Farm Name: Standard 14" Removable Side Extension: Optional Double Center Opening Doors: Optional Grain Kit (Top Pivot Door Only): Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Front to Back Scissor Tarp (Electric): Optional Side to Side Roll Tarp (Electric): Optional
	Meyer 9128 Industrial Rear Unload Forage Box
	9100 Series Difference Our Proven 8100 "Boss" Design - Plus: *Double drive main roller #120 x 2 *High capacity hydraulic drive *Reinforced, enclosed side frame *Stainless steel sides *Gate delay system *Marker lights and DOT reflective tape *Lengths up to 36' All Standard Equipment Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: - 16" Centers on Tubular Uprights - 16" Centers on Tubular Floor Supports - 16" Centers on Channel Cross Members - The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 28' 8" Inside Width: 98" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 29'5" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Ht. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 1390 Capacity (cu. ft. w/ extension): 1640 Max Net Load: 25 ton Roller Chain Drive - Aprons: #120 Apron Chains (Pintle): 667XH Rear Drive Shaft - Heavy Duty: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): Hydraulic Unload Time - PTO Drive (Approx): 60 sec. Stainless Steel Sides - Front & Back: Standard Superslide Solid Poly Floor: Standard Gate Delay System: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Roller Chain Oiler: Standard Rear Lights, Marker Lights & D.O.T. Tape: Standard Personalized Farm Name: Standard 14" Removable Side Extension: Optional Double Center Opening Doors: Optional Grain Kit (Top Pivot Door Only): Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Front to Back Scissor Tarp (Electric): Optional Side to Side Roll Tarp (Electric): Optional
	Meyer 9130 Industrial Rear Unload Forage Box
	9100 Series Difference Our Proven 8100 "Boss" Design - Plus: *Double drive main roller #120 x 2 *High capacity hydraulic drive *Reinforced, enclosed side frame *Stainless steel sides *Gate delay system *Marker lights and DOT reflective tape *Lengths up to 36' All Standard Equipment Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: - 16" Centers on Tubular Uprights - 16" Centers on Tubular Floor Supports - 16" Centers on Channel Cross Members - The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 30' Inside Width: 98" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 30'9"" Overall Width: 102" Overall Height - Tailgate w/o ext.: 103" Overall Height - Tailgate w/ ext.: 114" Overall Side Ht. - (No ext. / with ext.): 90/104" Stringer Width (truck Mount): 33.5" Capacity (cu. ft. w/out extension): 1460 Capacity (cu. ft. w/ extension): 1720 Max Net Load: 25 ton Roller Chain Drive - Aprons: #120 Apron Chains (Pintle): 667XH Rear Drive Shaft - Heavy Duty: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): Hydraulic Unload Time - PTO Drive (Approx): 60 sec. Stainless Steel Sides - Front & Back: Standard Superslide Solid Poly Floor: Standard Gate Delay System: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Roller Chain Oiler: Standard Rear Lights, Marker Lights & D.O.T. Tape: Standard Personalized Farm Name: Standard 14" Removable Side Extension: Optional Double Center Opening Doors: Optional Grain Kit (Top Pivot Door Only): Optional Truck Mount Kit w/steel fenders: Optional Factory Installation of Trk. Mt. Kit: Optional Front to Back Scissor Tarp (Electric): Optional Side to Side Roll Tarp (Electric): Optional
	Meyer 9130T Industrial Rear Unload Forage Box
	9100 Series Difference Our Proven 8100 "Boss" Design - Plus: *Double drive main roller #120 x 2 *High capacity hydraulic drive *Reinforced, enclosed side frame *Stainless steel sides *Gate delay system *Marker lights and DOT reflective tape *Lengths up to 36' All Standard Equipment Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: - 16" Centers on Tubular Uprights - 16" Centers on Tubular Floor Supports - 16" Centers on Channel Cross Members - The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 30' Inside Width: 98" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 30'9" Overall Width: 102" Overall Height - Tailgate w/o ext.: 145.5" Overall Height - Tailgate w/ ext.: 159.5" Overall Side Ht. - (No ext. / with ext.): 129.5/143.5" Stringer Width (truck Mount): N/A Capacity (cu. ft. w/out extension): 1460 Capacity (cu. ft. w/ extension): 1720 Max Net Load: 30 ton Roller Chain Drive - Aprons: #120 Apron Chains (Pintle): 667XH Rear Drive Shaft - Heavy Duty: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): Hydraulic Unload Time - PTO Drive (Approx): 90 sec. Stainless Steel Sides - Front & Back: Standard Superslide Solid Poly Floor: Standard Gate Delay System: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Roller Chain Oiler: Standard Rear Lights, Marker Lights & D.O.T. Tape: Standard Personalized Farm Name: Standard 14" Removable Side Extension: Optional Double Center Opening Doors: Optional Grain Kit (Top Pivot Door Only): Optional Truck Mount Kit w/steel fenders: Standard Factory Installation of Trk. Mt. Kit: N/A Front to Back Scissor Tarp (Electric): Optional Side to Side Roll Tarp (Electric): Optional
	Meyer 9136T Industrial Rear Unload Forage Box
	9100 Series Difference Our Proven 8100 "Boss" Design - Plus: *Double drive main roller #120 x 2 *High capacity hydraulic drive *Reinforced, enclosed side frame *Stainless steel sides *Gate delay system *Marker lights and DOT reflective tape *Lengths up to 36' All Standard Equipment Fully Welded Frame - NO BOLTS! This frame is designed to carry heavy loads day after day! It includes: - 16" Centers on Tubular Uprights - 16" Centers on Tubular Floor Supports - 16" Centers on Channel Cross Members - The welded construction will not bow or bend, and is a perfect fit for truck & trailer frames. You won't see the flexing and twisting associated with competetive boxes. Inside Length: 36' 8" Inside Width: 98" Inside Height (w/out extension): 72.5" Inside Height (w/ extension): 86.5" Overall Length: 37'5" Overall Width: 102" Overall Height - Tailgate w/o ext.: 145.5" Overall Height - Tailgate w/ ext.: 159.5" Overall Side Ht. - (No ext. / with ext.): 129.5/143.5" Stringer Width (truck Mount): N/A Capacity (cu. ft. w/out extension): 1780 Capacity (cu. ft. w/ extension): 2105 Max Net Load: 30 ton Roller Chain Drive - Aprons: #120 Apron Chains (Pintle): 667XH Rear Drive Shaft - Heavy Duty: 2.5 Hvy Tubing Upright Spacing: 16" on Cntr Upright Construction: 2"x2" Tubing Power Source (540 RPM): Hydraulic Unload Time - PTO Drive (Approx): 90 sec. Stainless Steel Sides - Front & Back: Standard Superslide Solid Poly Floor: Standard Gate Delay System: Standard Automatic Roller Chain Tighteners: Standard Automatic Rear Door Latching: Standard Front Gate Viewing Window: Standard Semi-Automatic Roller Chain Oiler: Standard Rear Lights, Marker Lights & D.O.T. Tape: Standard Personalized Farm Name: Standard 14" Removable Side Extension: Optional Double Center Opening Doors: Optional Grain Kit (Top Pivot Door Only): Optional Truck Mount Kit w/steel fenders: Standard Factory Installation of Trk. Mt. Kit: N/A Front to Back Scissor Tarp (Electric): Optional Side to Side Roll Tarp (Electric): Optional

[Back to the top]